Cockpit Setup Options A322
Contents
1 Datalink
Name: Metar provider
Options: [0: Simulator weather | 1: Online weather]
Default: [0: Simulator weather]
When requesting METAR/TAF information, this option determines what source is used to get the weather from: Simulator weather polls P3D and ask the current weather at a location in the simulator. This gives you current information, but does not provide TAF information. Online weather will return real world information including TAF. This will only make sense if the simulator uses real world weather.
Name: Load Cargo/PAX
Options: [0: NO | 1: YES]
Default: [1: YES]
When importing a flightplan from SimBrief, this option determines if cargo and passengers are also loaded according to the simbrief flight plan.
Name: Load Fuel
Options: [0: NO | 1: YES]
Default: [1: YES]
When importing a flightplan from SimBrief, this option determines if fuel us also loaded according to the simbrief flight plan.
2 Units
Name: Weight
Options: [0: KG | 1: LBS]
Default: [0: KG]
Name: Time
Options: [0: Local time | 1: FS time]
Default: [0: Local time]
Name: Default baro
Options: [0: HectoPascal | 1: Inches]
Default: [0: HectoPascal]
Name: Takeoff shift
Options: [0: Meters | 1: Feet]
Default: [0: Meters]
3 Config
Name: Engine type
Options: [0: CFM | 1: IAE]
Default: [0: CFM]
Name: GPS type
Options: [0: Hybrid | 1: Autonomous]
Default: [0: Hybrid]
Name: Door logic
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: Automatic ground power
Options: [0: NO | 1: YES]
Default: [0: NO]
Name: Lateral deviation scales
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: Cargo heating
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: Backup speed and altitude
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: TCAS autopilot option
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: Reset FMS after landing or failure
Options: [0: NO | 1: YES]
Default: [0: NO]
Name: Standby altimeter
Options: [0: Stand alone | 1: Slaved to Cpt | 2: Slaved to F/O]
Default: [0: Stand alone]
Name: Steering system on yellow hyd
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: AC ESS FEED auto switching
Options: [0: NO | 1: YES]
Default: [0: NO]
Name: Lift improvement package
Options: [0: NO | 1: YES]
Default: [0: NO]
Name: Alt tape vertical deviation green
Options: [0: NO | 1: YES]
Default: [0: NO]
Name: Go Around engages NAV instead of GA TRK
Options: [0: NO | 1: YES]
Default: [0: NO]
Name: Navaid virtualization
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: Gnd Temp field in INIT page
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: Ice detection system installed
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: Voice Channel Spacing
Options: [0: 25Khz | 1: 8.33Khz]
Default: [1: 8.33Khz]
Name: Altitude temperature compensation
Options: [0: NO | 1: YES]
Default: [0: NO]
Name: FLS
Options: [0: NO | 1: YES]
Default: [0: NO]
Name: Terrain Peaks
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: Alternate flap timing Requires professional license
Options: [0: NO | 1: YES]
Default: [0: NO]
4 Audio
Name: GPWS 2500
Options: [0: NO | 1: YES]
Default: [0: NO]
Name: GPWS 2000
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 1000
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 500
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 400
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 300
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 200
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 100
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 50
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 40
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 30
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 20
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 10
Options: [0: NO | 1: YES]
Default: [1: YES]
Name: GPWS 5
Options: [0: NO | 1: YES]
Default: [1: YES]
5 QTG
All options require eQTG feature
Name: Transport Delay on Visual
Options: [0: Disabled | 1: Enabled]
Default: [0: Disabled]
Name: Transport Delay on Displays
Options: [0: Disabled | 1: Enabled]
Default: [0: Disabled]
Name: Flight Controls trigger transport delay
Options: [0: Disabled | 1: Enabled]
Default: [0: Disabled]
